Pharmaceutical Industrial Water Filter Housing / Water Filter Cartridge Housing

Pharmaceutical Industrial Water Filter Housing / Water Filter Cartridge Housing

SS Filter Housing consists of SUS316L or SUS304, and take filter cartridge as its element. The SS filter housing can be used for filtration of liquid, gas and 0.1um above particles and bacteria, with high removal rating and flow rate. It possess properties of lower absorption, no medium shedding, no leakage, acid and alkali Resistance, and corrosion resistance. In addition, it is easy to wash and function as back flush, and is ideal filtration equipment for the industry of biology & pharmacy, beer & beverage, chemical, and water treatment etc.

Operation

Contaminated fluid enters the housing and is distributed evenly around the filter cartridges. Filtration takes place from outside to inside. Solids are collected on the outside of filter cartridges & clear filtrate is collected at outlet.

Features & Benefits 

• Low pressure drop

• High dirt holding capacity

• Zero hold up design

• Permanently piped housing are opened without special tools and without disturbing the piping

• Machined cover gasket groove provide positive O-Ring sealing

• Easy to clean

• In-line inlet and outlet high flow rates

• Positive sealing arrangement to avoid bypassing

• Suitable for double open end (DOE), 226 O-Ring & 222 O-Ring type filter cartridge

• Accommodates 10", 20", 30", 40", 50” & 60” long filter cartridges.

• End connections of ¾" to 24" pipe

• V posts or threaded center posts

• Quick opening tri clovers design

• Easy to operate & low maintenance

• Low down time 3

• Flow rate up to 2000 m /hr & more

• Customized design available

• Housings are permanently piped

• All housings made from SS 316 L, SS 316 & SS 304 are mirror polished & electro polished to resist adhesion of dirt and scale

• Duplex / Triplex / Jacketed cartridge filter unit designs are available 

• High temperature & high pressure designs are available

CHUNKE Housing Cartridge Filter Installation

 

Figure 1 below shows a common filter housing installation setup. This setup will facilitate filter installation and the sanitization and sterilization of filters during use.

 

CHUNKE Cartridge Filters should, at minimum, be installed in a housing system as shown in Figure 1 with the valves and pressure gauges in place for the “Product In” line. If the cartridge is being installed in a system that will be heat sanitized or steam sterilized, then the lines, valves, pressure gauges and temperature gauges for “Hot Water In” and/or “Steam In” should also be in place. If the filter is to be integrity tested, then the mass flow meter portion of the system in Figure 1 should also be installed.

Procedures for integrity testing filters as well as procedures for hot water sanitization, steam sterilization and chemical sanitization and to get more info please contact with us.

 

Figure 1. Cartridge filter housing installation diagram

 

1. Shut off flow by first closing valve V1, and making sure that valves V2, V3 , V4 and V5 are also closed. Then close all other valves open during operation. (Caution: Do not open the housing until pressure gauges G4 and G5 both show “0” pressure.)
2. .Open Vent (Valve 7) and Drain (Valve 6) to empty housing of liquid. Open downstream drain valve V10, if desired.
3. Remove the housing bowl and remove the old filter.
4. Open the bag containing the new filter at the end with o-rings and wet the o-rings with water or the fluid beingvfiltered. DO NOT TOUCH THE FILTER WITH BARE HANDS OR FINGERS.
5. .With the new filter still in the bag, push the o-ring end into the filter housing head using a twisting motion to assure a complete seal. If the filter has a 2-226 or 2-223-Tab o-ring configuration, make sure that the locking tabs engagev with the tab holders in the housing head. (To prevent inadvertent contamination of filter, do not directly touch filters with your hands.)
6. Remove the bag and replace the filter housing bowl.
7. Close the Vent (V7) and Drain (V6 and/or V10).

 

Quality Standard

 

Our goal is to ensure our customers the greatest possible value for their filtration dollar. Our state of the art manufacturing facility and quality management system both meet ISO 9001:2008 standards. Each operation from assembly and test to cleaning, drying, and packaging is done in appropriately rated clean rooms. CHUNKE computer system collects and processes real time data from manufacturing centers and inspection points. This allows variable and attribute data to be quickly and easily analyzed driving constant improvements in both quality and cost.

 

CHUNKE is a vertically integrated manufacturer of filtration products to industries in which filtration is considered a critical part of the manufacturing process. We supply a complete line of products and services to help you cost effectively satisfy all your filtration requirements from a single source.